Products
Modular I/O
System Module
M-SPE : System Power Extension Module
In a modular IO station, Header module provides system power supply for IO modules. This supply is connected to IO modules through pins and receptacles interface of each module. If number of IO modules attached to Header module increases, system power consumption increases and then the system power supply provided by Header module will not be sufficient. In such case, user needs to add system power supply extension module in the station.
| Specification | Description | |
|---|---|---|
| Module Ordering Code | M-SPE | |
| System Power Supply | Input voltage | 24 VDC (11 to 28.8 VDC, ripple included), 12 Watt |
| Inrush current | 20 A for 20 µsec duration | |
| Output voltage | 5 VDC | |
| Output current for IO modules | 2 A | |
| Protection | Reverse polarity protection | |
| Isolation | Non-isolated | |
| Field Power Supply | Voltage | 24 VDC (18 to 30 VDC, ripple included) |
| Maximum input current at 24 VDC | 5 A per input terminal | |
| Current | 10 A | |
M-FPD: Field Power Distribution Module
In a modular IO station, field power distribution module M-FPD provides additional terminals for the field power supply. Module M-FPD provides 8 terminals out of which 4 terminals provide 24 VDC and 4 terminals provide 0 VDC connections. It avoids use of extra terminals in the control panel and facilitates ease of sensor and actuator connections.
| Specification | Description |
|---|---|
| Module Ordering Code | M-FPD |
| Field Voltage | 24 VDC, 0 VDC |
| Field power contact Current | Max. 10 Amps. |
M-FPI: Field Power Isolator Module
In a modular IO station, field power supply is connected to a Header module. This supply is connected to IO modules through pins and receptacles interface of each module. Capacity of pins and receptacles interface of modules is 10A maximum.
| Specification | Description |
|---|---|
| Module ordering code | M-FPI |
| Field voltage | 5 VDC/ 12 VDC/ 24 VDC/ 48 VDC/ 110 VAC/ 220 VAC |
| Field power contact current | 5 A per input terminal |
M-ST: Shield Termination Module
In a modular IO station, shield termination module M-ST provides terminals to connect shield of cables carrying low level signals like analog, communication, etc. So, it is recommended to attach module M-ST after IO module which provides such interfaces e.g. M-UAD2, M-DA2 where analog IOs are connected.
| Specification | Description |
|---|---|
| Module ordering code | M-ST |
| Number of shield terminals | 8 |
| Contact current at terminal | 5 A per input terminal |
M-BE: Bus End Module
In a modular IO station, bus end module M-BE provides termination to backplane bus. User should attach bus end module M-BE at the last slot position if there are 16 or more IO modules.
| Specification | Description |
|---|---|
| Module Ordering Code | M-BE |
| Terminating Resistor | 120 Ω / QW |
| Power Dissipation | Nil |
M-B2, M-B3 and M-B5: 2/3/5 Slots Base Module
For Modular IO station with header assembly, assembly modules are mounted on base module. Base module provides 5 Vdc from Power supply module to other modules fixed on it and to IO modules via adapter module.
| Item | Description | |||
|---|---|---|---|---|
| Ordering Code | M-B2 | M-B3 | M-B5 | |
| Number of Slots | 2 | 3 | 5 | |
| No. of PSU Slots | 1 | 1 | 2 | |
| No. of Header Slots | 1 | 1 | 2 | |
| No. of ADP Slots | No* | 1 | 1 | |
| Mounting | DIN rail (35 x 7.5 x 1 mm) | |||
M-APSU: Redundant AC Power Supply Module
M-APSU is 110/220 VAC Input Power Supply module which is a Header assembly module. M-APSU module can be mounted in PSU slot of 3-slots base module (M-B3) and 5-slots base module (M-B5). M-APSU module is designed for redundant operation and works on the principle of load sharing with another M-APSU module.
| Specification | Description | ||
|---|---|---|---|
| Module Ordering Code | M-APSU | ||
| Mounting | On Base module M-B3 and M-B5 | ||
| Position on Base Module | PSU slot on base module | ||
| Input Voltage | 100 to 240 VAC (Range from 85 to 264 VAC) | ||
| Input Frequency | 50/ 60 Hz -6%/ +4% | ||
| Maximum Input Apparent Power | 90 VA | ||
| Inrush Current | 20 A, 8 ms or less | ||
| Rated Output Voltage | 5 VDC; 3.5 A (2A for IO modules) |
||
| Parallel Connection | Permitted for redundancy operation with load sharing. | ||
| Allowable Momentary Power Failure | >20 ms at 220 VAC at full load at an ambient of 55 °C >10 ms at 110 VAC at full load at an ambient of 55 °C |
||
| Protection | Output over current | 4.4 A or higher | |
| Output short circuit | Yes | ||
| Input overvoltage | Yes | ||
| Internal fuse at input side | Built-in (Unchangable by user) | ||
| Over temperature | Yes | ||
| Potential Free Contact Output | Application | ERR contact | |
| Rated switching voltage current | 220 VAC/ 24 VDC, 0.5 A | ||
| Minimum switching load | 1 mA | ||
| Response time | Off to On | 10 ms or less | |
| On to Off | 10 ms or less | ||
| Life | Mechanical | 20 million times max. (180 cpm) | |
| Electrical | 100,000 times max. | ||
| Surge suppressor | None | ||
| Fuse protection | None | ||
| Module status indication | PW: 1 no., Green LED LD: 1 no., Amber LED |
||
| Withstand voltage (EN 50178) | 2300 VAC rms per minute (Between line input terminals and FG terminals and output) | ||
| Insulation resistance | 100 MΩ or higher by 500 VDC insulation resistance tester (between line input terminals and FG terminals and output) |
||
| Hot swapping | Supported. | ||
M-DPSU: 24 VDC Power Supply Module
M-DPSU is 24 VDC Input Power Supply module which is a Header assembly module. M-DPSU module can be fixed in rightmost slot of 2-slots base module (M-B2).
| Specification | Description | ||
|---|---|---|---|
| Module Ordering Code | M-DPSU | ||
| Mounting | On Base module M-B2 | ||
| Position on Base Module | PSU slot on base module | ||
| Input Voltage | 24 VDC (Range from 18 to 30 VDC) | ||
| Maximum input power | 20 Watts | ||
| Inrush current | 70 Amps, for 500 micro sec or less | ||
| Rated output voltage | 5 VDC; 3 A (2A for IO modules) |
||
| Output ripple | 20 mV (p – p) maximum | ||
| Allowable momentary power failure | Less than 10 ms at 24 VDC at full load at an ambient of 55 °C | ||
| Protection | Output over current | Yes. 3.9 Amps or higher | |
| Output short circuit | Yes | ||
| Input polarity reversal | Yes | ||
| Input transient | Yes | ||
| Input overvoltage | Yes | ||
| Internal fuse at input side | Yes. Built-in (Unchangable by user) | ||
| Over temperature | Supported | ||
| Module status indication | 1 no., Green LED (PW) | ||
| Module status and diagnostics | LED indication for local monitoring. | ||
| I/O memory consumption | Nil | ||
| Withstand voltage | Between primary and 5VDC terminal | 510 VAC per minute; | |
| Insulation resistance | Between line input terminals and output) | 100 MΩ or higher by 500 VDC insulation resistance tester | |
| Hot swapping | Not supported | ||
M-ADP: I/O Adapter Module
M-ADP is I/O Adapter module which is a Header assembly module. M-ADP module can be mounted in ADP slot i.e. the rightmost slot on 3-slots base module (M-B3) and 5-slots base module (M-B5).
| Specification | Description |
|---|---|
| Module Ordering Code | M-ADP |
| Mounting | On Base module M-B3 and M-B5 |
| Position On Base | ADP slot i.e. rightmost slot on base module |
| LED Indication | I/O PW Green LED: 24 VDC field power supply is healthy |
| Contact Current at Terminal | 5 A per input terminal |
M-BC: Blank Cover Module
In a modular IO station, blank cover module M-BC has no external connections. User should attach blank cover module M-BC at the last slot position in Header assembly configuration.
| Specification | Description |
|---|---|
| Module Ordering Code | M-BC |
| Mounting | On base module (M-B5) |
| LED Indication | Not available |
| Connection | Not supported |